Introduction
Micro electric ball valves and butt welded ball valves are divided into integral (one-piece), two-stage, and three-stage types. The valve body is cast using advanced technology, with a reasonable structure and beautiful appearance. The valve seat adopts an elastic sealing structure, which is reliable in sealing and easy to open and close. The valve stem adopts a sealed bottom mounted structure, and when the valve chamber is abnormally pressurized, the valve stem will not be flushed out. Two piece and three piece ball valves can also be connected by butt welding (BW) and socket welding (SW), and both can be equipped with international standard ISO bracket platforms and locking devices. A 90 degree switch positioning mechanism can be set, and locks can be added as needed to prevent accidental operation.
Technical Parameter
Specifications
| Nominal Diameter | DN10 - 100mm | Nominal Pressure | PN1.6, 2.5, 4.0, 6.4, 31.5Mpa (Customizable) | ||||
|---|---|---|---|---|---|---|---|
| Connection Method | Internal Thread Connection | Butt - Welded Connection | |||||
| Part Name | Valve Body and Bonnet | WCB | CF8(304) | CF8M(316) | WCB | CF8(304) | CF8M(316) |
| Ball and Stem | 2Cr13 | 0Cr19Ni9 | 0Cr17Ni12Mo2 | 2Cr13 | 0Cr19Ni9 | 0Cr17Ni12Mo2 | |
| Sealing Ring and Packing | Reinforced Polytetrafluoroethylene, Para - polyphenylene | ||||||
| Applicable Working Conditions | Applicable Medium | Water, Steam, Oil, etc. | Corrosive Media such as Nitric Acid | Corrosive Media such as Acetic Acid | Water, Steam, Oil, etc. | Corrosive Media such as Nitric Acid | Corrosive Media such as Acetic Acid |
| Applicable Temperature | -29°C - 180°C (Reinforced Polytetrafluoroethylene), -29°C - 300°C (Para - polyphenylene) | ||||||
(The dotted part is the analog control box, which is not applicable to the switch type.)
External Dimensions and Connection Dimensions
| G | ΦD | B | H1 | H | L1 | L2 | L3 |
|---|---|---|---|---|---|---|---|
| 1/4’ | 11.2 | 60 | 148 | 35 | 50 | 40 | 123 |
| 3/8’’ | 12.5 | 60 | 148 | 35 | 50 | 40 | 123 |
| 1/2’’ | 15 | 75 | 163.5 | 35 | 65 | 40 | 160 |
| 3/4’’ | 20 | 80 | 171.5 | 39 | 65 | 40 | 160 |
| 1’’ | 25 | 90 | 179.5 | 50.5 | 65 | 40 | 189 |
| 1-1/4’’ | 32 | 110 | 184 | 55.5 | 65 | 40 | 189 |
| 1-1/2’’ | 38 | 120 | 195 | 66 | 82 | 40 | 189 |
| 2’’ | 50 | 140 | 197.1 | 68.1 | 82 | 40 | 189 |
| 2-1/2’’ | 65 | 185 | 222.5 | 93.5 | 82 | 40 | 189 |
| 3’’ | 76 | 205 | 233 | 104 | 82 | 40 | 189 |
| 4’’ | 100 | 240 | 241 | 112 | 116 | 40 | 266 |
Valve Installation & Maintenance
Valve Installation:
(1) Before installation, check that the product model, tag number, and specifications match the requirements. Inspect the entire valve for missing or loose parts.
(2) Prior to installation, clean the pipeline. Ensure there is sufficient straight pipe section at the valve inlet and install a filter. When connecting the valve body to the pipeline flanges, ensure coaxiality.
(3) Thoroughly clean the pipeline before installing the valve.
(4) The installation site should ensure the safety of personnel and equipment, facilitating operation, disassembly, and maintenance.
(5) The valve should be installed vertically upright on horizontal pipelines. If necessary, it can be installed at an angle, but horizontal installation should be avoided. For occasions with heavy valve weight or vibration, use a support frame.
(6) The medium flow direction must align with the arrow on the valve body. The air supply should be dry and oil-free. The valve should be used in environments with temperatures ranging from -20℃ to 55℃.
(1) Before installation, check that the product model, tag number, and specifications match the requirements. Inspect the entire valve for missing or loose parts.
(2) Prior to installation, clean the pipeline. Ensure there is sufficient straight pipe section at the valve inlet and install a filter. When connecting the valve body to the pipeline flanges, ensure coaxiality.
(3) Thoroughly clean the pipeline before installing the valve.
(4) The installation site should ensure the safety of personnel and equipment, facilitating operation, disassembly, and maintenance.
(5) The valve should be installed vertically upright on horizontal pipelines. If necessary, it can be installed at an angle, but horizontal installation should be avoided. For occasions with heavy valve weight or vibration, use a support frame.
(6) The medium flow direction must align with the arrow on the valve body. The air supply should be dry and oil-free. The valve should be used in environments with temperatures ranging from -20℃ to 55℃.
Valve Maintenance:
(1) Cleaning the Valve: For general media, cleaning with water is sufficient. For media harmful to health, first understand their properties and then select an appropriate cleaning method.
(2) Disassembly: Remove rust from exposed rusted parts first. Before derusting, protect the machined surfaces of precision parts such as the valve seat, valve plug, valve stem, and push rod. Use special tools when disassembling the valve seat.
(3) Valve Seat: Minor rust or wear on the sealing surface can be repaired by machining. If damage is severe, replace the seat. However, both repaired and replaced hard sealing surfaces must be lapped.
(4) Valve Stem: If the surface is damaged, it must be replaced.
(5) Damage to Push Rod, Guide, and Sealing Surfaces: Reverse-acting actuators must be replaced; direct-acting actuators can be reused after proper repair.
(6) Compression Spring: If there are cracks or other defects affecting strength, replace it immediately.
(7) Wear Parts: Packing, gaskets, and O-rings must be replaced entirely during each maintenance. Check the valve plug and diaphragm for cracks, aging, or corrosion that may cause future failures. Decide whether to replace them based on inspection results, but the diaphragm service life should not exceed 2-3 years.
(8) When reassembling the valve, ensure alignment. Tighten bolts diagonally and lubricate sliding parts. After reassembly, debug the valve according to the factory test items and methods. During this period, accurately adjust the packing compression force and the valve plug closing position.
(1) Cleaning the Valve: For general media, cleaning with water is sufficient. For media harmful to health, first understand their properties and then select an appropriate cleaning method.
(2) Disassembly: Remove rust from exposed rusted parts first. Before derusting, protect the machined surfaces of precision parts such as the valve seat, valve plug, valve stem, and push rod. Use special tools when disassembling the valve seat.
(3) Valve Seat: Minor rust or wear on the sealing surface can be repaired by machining. If damage is severe, replace the seat. However, both repaired and replaced hard sealing surfaces must be lapped.
(4) Valve Stem: If the surface is damaged, it must be replaced.
(5) Damage to Push Rod, Guide, and Sealing Surfaces: Reverse-acting actuators must be replaced; direct-acting actuators can be reused after proper repair.
(6) Compression Spring: If there are cracks or other defects affecting strength, replace it immediately.
(7) Wear Parts: Packing, gaskets, and O-rings must be replaced entirely during each maintenance. Check the valve plug and diaphragm for cracks, aging, or corrosion that may cause future failures. Decide whether to replace them based on inspection results, but the diaphragm service life should not exceed 2-3 years.
(8) When reassembling the valve, ensure alignment. Tighten bolts diagonally and lubricate sliding parts. After reassembly, debug the valve according to the factory test items and methods. During this period, accurately adjust the packing compression force and the valve plug closing position.
Ordering Instructions
When placing an order, please fill in the Specification Sheet or specify the following information:
-
If the model has not been selected before ordering, please provide us with the operating parameters:
(1) Nominal diameter DN (mm);
(2) Nominal pressure (MPa or bar);
(3) Fluid properties (including medium temperature, viscosity, or acidity/alkalinity);
(4) Pressure before and after the valve (pressure differential);
(5) Requirements for flow characteristics;
(6) Materials of valve body and valve core;
(7) Connection type;
(8) Driving method (provide air supply pressure, driving voltage);
(9) Supporting accessories (for pneumatic valves, it is recommended that users install an air filter triplet and a 2-position 5-way solenoid valve);
(10) On-site working conditions. -
If the product model of our company has been selected by the design unit, please order directly from our production department according to the model;
-
When the application occasion is very important or the pipeline is relatively complex, please provide the design drawings and detailed parameters as much as possible, and our experts will review and check them for you.
